LTC 8016/90 Allegiant Bilinx Data Interface

Commercial Type No.: LTC 8016/90
Product No.: F.01U.506.853

LTC 8016/90 Allegiant Bilinx Data Interface
  • Bilinx technology interface for Allegiant Series matrix switcher/controllers
  • Up-the-coax Pan/Tilt/Zoom (PTZ), auxiliary, and pre-position control
  • Down-the-coax event reporting
  • Auto-sensing setup for simplified installation
  • Data input allows other devices to control Bilinx PTZ cameras
  • Cascade units to control up to 496 Bilinx cameras
  • Overview
    Voltage Range 108 to 264 VAC, 50/60 Hz
    Power at Rated Voltage 15 W
    Maximum Video Signal Distances
    Coax Up to 300 m (1000 ft) using standard CCTV-grade RG-59U with copper center conductor and copper braided shield; up to 600 m (2000 ft.) using CCTV-grade RG-11 or RG-6.
    Fiber Up to 600 m (2000 ft) using LTC 4630 and LTC 4631 Series fiber optic modules. Note: This distance includes the length of coax cables used between the devices and the fiber optic link.
    Other Up to 230 m (750 ft) using CAT5E cable that meets ANSI/TIA/EIA-568-A requirements with NV-211 or NV-214 A-M BNC-to-twisted Balun devices (or similar passive device pair). Note: When using twisted pair links of this type, some degradation in video quality may be experienced at distances beyond 150°m (500°ft).
    Front Panel Indicators
    Status / Power LED
    Rear Panel Indicators
    System Data Link Indicator Green LED
    Data Activity Indicator Yellow LED
    Bi-Phase Code Indicator Green LED
    Bilinx Video Signal Presence One (1) green LED for each of 16 channels
    Ethernet Port Green LED indicates link; Yellow LED indicates activity
    Rear Panel Controls
    Group ID Three (3) rotary switches
    Rear Panel Connectors
    Bilinx Video Inputs 16 BNC connectors; accepts standard NTSC/PAL baseband composite video signals or video signals from Bilinx-capable cameras; 0.5–1.4 Vp-p; 75 Ohm terminated; TVS protected inputs provide improved protection against transients
    Video Outputs Male 34-pin video ribbon connector; provides 16 video outputs (unity gain using active circuitry); mating 2 m (6°ft) 16-channel LTC 8809/00 cable included
    Bi-Phase Data Interface 6-position removable terminal block with "+"," –", and "shield" input connections and "+"," –", and "shield" looping output connections, with attached end-of-line termination resistor
    PC Interface Male 9-pin sub D-connector
    RS-232 Data Interface1 Female 9-pin sub D-connector for Allegiant RS-232 interface
    RS-485 Data Interface1 Female 9-pin sub D-connector for Allegiant RS-485 interface port connection
    RS-485 ‘Looping’ Data Interface1 Female 9-pin sub D-connector, for data interface to cascaded LTC 8016 unit
    1.One (1), 2 m (6 ft) data interface cable is supplied for use with the Allegiant RS-232 interface, the Allegiant RS-485 interface, or the cascade configuration looping connection.
    Ethernet Interface RJ-45 connector, supporting 10/100 BaseT (reserved for future use)
    Power Cord Two (2) detachable 3-wire IEC cords with grounded plug, 1.83 m (6 ft.); one with European continental plug type and one with US plug type
    Temperature
    Operating 0°C to 50°C (32°F to 122°F)
    Storage –10°C to 70°C (14°F to 158°F)
    Humidity 0% to 90% relative, non-condensing
    Construction Steel chassis with sheet metal cover and plastic bezel
    Finish Charcoal case
    Dimensions (W x D x H) 440 x 305 x 40 mm (17.3 x 12 x 1.7 in.)
    Weight 3.8 kg (8.5 lb)
    Rack-mount Kit (included) For mounting unit in an EIA 48 cm (19 in.) rack
    LTC 8508/01 Ribbon-to-BNC Interface Cable
    Interface cable with a 34-pin ribbon cable on one end and 16 male BNC connectors on the other end. This cable is required when the LTC 8016 unit will be connected to control system devices that do not contain a 34-pin ribbon cable connector.
    LTC 8807/00 BNC Panel Interface panel used to convert video ribbon cables from up to two LTC 8016 units into 32 standard female BNC connectors. Useful when the LTC 8016 unit will be separated from the control unit beyond the 2 m (6 ft)distance allowed by the video ribbon cable supplied with the unit.
    LTC 4630, LTC 4631 Fiber Optic Series modules compatible with Bilinx communication. Available in surface-mount and rack- mount models. Refer to the LTC 4600 Series data sheet for complete information on these products.
    NV‑211 or NV‑214 A‑M BNC-to-twisted pair adaptors passive (non-amplified) devices compatible with Bilinx technology, allowing transmission of real-time monochrome or color video over unshielded twisted pair (UTP) telephone wire. Refer to the NV-214 A-M Series data sheet for complete information on these products.
    Allegiant Matrix Switchers Requires an Allegiant CPU firmware 8.6 or later (released May 2004)
    AutoDome Cameras All models manufactured October 2003 (version 5.11), or later
    Dinion Cameras Dinion Series manufactured March 2004, or later
    Bi-Phase Devices Any product generating standard Allegiant Bi-Phase Control Code protocol

    Images

     
  • Documents (8)
 

Accessories

LTC 8508/01 Ribbon-to-BNC interface cable

for LTC 8016, with a 34-pin ribbon cable on one end and 16 male BNC connectors on the other end, 1 m (3 ft)

Commercial Type No.: LTC8508/01
Product No.: F.01U.506.854

 

LTC 8807/00 BNC Panel

32 channel video interconnect panel, for use with up to 2 LTC 8809 video ribbon cables

Commercial Type No.: LTC 8807/00
Product No.: F.01U.002.517

 
 

NV-213A UTP-NVT 1 CH PASSIVE

Passive (non-amplified) devices compatible with Bilinx technology, allowing transmission of real-time monochrome or color video over unshielded twisted pair (UTP) telephone wire. Refer to the NV‑231A Series Data Sheet for complete information on these products.

Commercial Type No.: NV-213A
Product No.: F.01U.507.404